1 Introduction
This overview briefly presented the key multifunction feature of Flying Voice products. For more information on the key multifunction feature, please refer to the specific user manual.
Our IP652 and IP622 can support the multifunction key feature. The IP622 has 10 multifunction keys, and the IP652 can support a total of 260 multifunction keys with 20 on the base board and the rest on EXP40 cards (the IP652 can support up to six EXP40 cards, each EXP40 card having 40 multifunction keys).
You can configure the multifunction key for speed dialing, BLF, shortcut, call pickup, and call parking. Each multifunction key supports five functions, and you can configure them as you wish.
Note: BLF and call parking require support from your SIP server or PBX, so please check with your provider or administrator before using or testing.
2 Configuration
En supposant que vous souhaitiez utiliser la fonction de touche multifonction sur IP652 ou IP622, vous devez d'abord vous connecter au web pour ouvrir la page Phone/Multi-Functional Key avant la configuration.
Image 1
Web Phone/Multi‑function Key Page
2.1 Web Page
Image 2 below is the configuration page of the IP622, and image 3 is that of the IP652:
Image 2 IP622 Configuration Page
Image 3 IP652 Configuration Page
2.2 Configurable Parameters
Table 1 above explains the definition of the parameters.| Parameters | Definition |
![]() |
Choose a card for configuration |
![]() |
The serial number of the multifunction key |
![]() |
The type you want to configure, there are five: speed dial, BLF, shortcut key, call transfer and call waiting. |
![]() |
The function mode of the shortcut key you want to configure for the exp key. Configurable when the type is a shortcut key. |
![]() |
La ligne que vous souhaitez configurer, auto occupe la priorité la plus élevée de la ligne enregistrée, la priorité va de la ligne 1 à la ligne N (pour IP652, N = 5 ; pour IP622, N = 2). |
![]() |
Enter the phone number you wish to configure. Configurable when the Type is configured for speed dialing, BLF, call capture, and call waiting. |
![]() |
Set the support code. Configurable when the type is BLF. |
Table 1 Parameter definition
2.3 Configuration steps
You can follow the steps below to configure the multifunction key:
Step 1. If you have IP652, choose a current keyboard to configure from Basic Board, Expansion
Card N (1/2/3/4/5/6).
Step 2. Choose an Exp key you want to configure.
Step 3. Choose a function type among speed dial, BLF, shortcut key, call capture, and call hold.
Step 4. Set the other corresponding parameters.
Step 5. Press
to save the changes, then you will see the LED under the corresponding touch button (except BLF) light up green (green indicates the function is active).
Step 6. If you configure an exp key to BLF, the LED will remain off and the indicator will appear; you must restart the device for the changes to take effect, then the LED will turn green.
Step 3. Press
bouton pour enregistrer les modifications puis appuyez
button to make changes effective.
to save the changes, then you will see the LED under the corresponding touch button (except BLF) light up green (green indicates the function is active).
Step 6. If you configure an exp key to BLF, the LED will remain off and the indicator will appear; you must restart the device for the changes to take effect, then the LED will turn green.
3 Functions
3.1 Quick dialing
3.1.1 Creating quick numbers
Step 1. Access the web, then open the Phone/Multi-Functional Key page Step 2. Configure an Exp key for speed dialing, then choose the line and enter the phone number. The following image 4 is an example of configuration:
Step 3. Press
bouton pour enregistrer les modifications puis appuyez
button to make changes effective.
|
Above are the steps to create speed dials from the web page; You can also create it from the LCD menu (Menu/Multifunction key item). 3.1.2 Using speed dials |
3.2 BLF (Busy Lamp Field)
This feature requires your PBX support, so please check with your provider or administrator before testing or using.
3.2.1 BLF
Your system administrator can configure your phone so you can monitor other users’ phones from your device. The user can create a BLF from the Multi‑Function menu/Button or from your PC on the Web Phone/Multi‑Functional Key page.
If this function is configured, some multifunction buttons on your phone are assigned to display the status of another user's phone.
For example, if your single multifunction key is set to display Bob’s phone line, the associated multifunction key will show the status of his phone line as shown in Table 2:
| LED Status | Monitored phone action |
| Green | The line is idle |
| Red (stable) | The line is active or in use |
| Red (blinking) | The line rings |
Table 2
3.2.2 Support code in BLF
Additionally, if you have configured the pickup code in the BLF, you can press the same multifunction button to answer a ringing call on your station.
The example below describes the steps to configure BLF pickup from the web page; the user can also configure it from the LCD MENU.
Access the web, then open the Phone/Multi‑Functional Key page
Next, configure an Exp key for BLF, and set the pickup code (you can obtain the pickup code from your administrator).
The following image is an example of configuration based on Asterisk 1.6 (Asterisk 1.6 supports BLF Pickup functions).
Adding the pickup code:
Step 1. Enter the support code provided by your administrator or your IPPBX.
Step 2. Press
button to save changes then press the button to make the changes effective.
Image below 5 configured a BLF to monitor the 003 on line3 with support function.
button to save changes then press the button to make the changes effective.
Image below 5 configured a BLF to monitor the 003 on line3 with support function.
Image 5 Example of BLF
To answer an incoming call:
Assuming a ringing call to 003, the LED light under Exp Key 1 will blink red.
You can press line 3 button (by default line 1), then press Exp 1 key to answer the incoming call.
3.3 Shortcut Key
The steps above describe how to configure the shortcut key from the Web page; the user can also configure it from the MENU.
3.3.1 Creation
Shortcut:
Step 1. Go to the web, then open the Phone/Multi‑Functional Key page
Step 2. Then configure the Exp keys as shortcut keys, and set them according to your needs. The following image 6 is an
example of configuration :
Image 6 Shortcut key example
Step 3. Press
bouton pour enregistrer les modifications puis appuyez
button to apply changes.
bouton pour enregistrer les modifications puis appuyez
button to apply changes.
3.3.2 Usage
keyboard shortcut:
Press the Exp 1 key, then the LCD screen will immediately display the directory item, and the user can configure it; the steps are the same as configuring from the menu.
Press the following Exp keys, and the LCD screen will immediately display the corresponding item; the user can also configure it.
3.4. Pick up
The call‑taking function is similar to speed dialing. The example below describes the steps to configure pickup from the web page; the user can also configure it from the MENU.
3.4.1 Add support
Step 1: log in to the web, open the Phone/Multi‑functional Key page.
Step 2. Choose an Exp key (assuming it’s Exp 3), and configure as shown in image 7
Image 7 Call capture example
3.4.2 Using pickup
Press the Exp Key 3 button (the configured multifunction key) to quickly dial 010235689.
3.5 Call Station
Cette fonction nécessite le support de votre IPPBX, veuillez donc vérifier auprès de votre fournisseur ou administrateur avant de tester ou
en utilisant.
3.5.1 Call waiting
Call parking is a function of some telephone systems that allows a person to put a call on hold on a telephone
define and continue the conversation from any other handset.
During an active call, press a pre‑programmed multi‑function button to transfer the ongoing telephone conversation to an unused line. extension number and immediately put the conversation on hold. The telephone system will then display the extension number of
the held call so that the call can be retrieved later.
If no one answers the held call within the defined time, the telephone system can redial the held call. This transfers the held call to the person who originally put it on hold.
The example below describes the steps to configure call park from the Web page; the user can also
configure from the LCD MENU.
3.5.2 Add
Call Park
Step 1: Display parking settings on the server, below is an example in TrixBox
Image 8 TrixBox parking settings
Step 3. Choose an Exp key (assuming it’s Exp 6), and configure as shown in image 9
Image 9 Call parking example
Step 4. Press
bouton pour enregistrer les modifications puis appuyez
button to apply changes.
bouton pour enregistrer les modifications puis appuyez
button to apply changes.
3.5.3 Using Call Park
Step 1. During an active call (assuming party 1’s number is 6221, party 2’s number is 111)
Step 2. Participant 1 presses the Exp Key 6 button (configured
Multifunction key) to put the ongoing conversation on hold and patiently listen to the voice prompt (with TrixBox, you will hear 71, which is the extension number).
Step 3. Participant 3 dials 71 to retrieve the call with participant 2.







