The Multi‑WAN is used to deliver different types of services, and the device’s Multi‑WAN supports data services, voice services, and management services. By configuring different VLANs, different types of data must be routed to the corresponding network, for example, the INTERNET VLAN and Other VLAN support data transmission, the VOICE VLAN supports voice transmission, and the TR069 VLAN supports WEB, telnet, and TR069 service transmission.
There are several advanced features on the Multi WAN setting:
The PPPoE bridge can allow PPPoE packets to pass, which can prevent L2 packet flooding to LAN ports.
The HW bridge can function as an L2 switch to increase throughput between the WAN and LAN.
The trunk VLAN can allow marked packets to be directed straight to LAN ports.
IPTV can be supported with other LAN ports linked to VLAN.
2. Internet connection configuration
From the WAN page, a multi‑WAN connection can be created or removed. Below is the default WAN configuration.
2.1 Connect name and service
The connection names table is below:
|
Content
|
Set |
Commentary
|
|
No
|
1~99
|
WAN login ID
|
|
Service
|
TR069
|
The connection only supports management applications, such as TR069, WEB, SNMP and Provision
|
|
|
INTERNET
|
The connection only supports Internet service
|
|
|
TR069_INTERNET
|
The connection supports management and Internet applications
|
|
|
VOICE
|
The connection only supports voice applications, such as SIP and RTP
|
|
|
TR069_VOICE
|
The connection supports both management and voice application
|
|
|
VOICE_INTERNET
|
The connection supports voice and Internet applications
|
|
|
TR069_VOICE_INTERNET
|
The connection supports management, voice, and Internet applications
|
|
|
Other
|
The connection supports the STB
|
|
NAT Mode
|
B
|
Bridge |
|
|
R
|
Router |
|
VLAN ID
|
VID
|
VLAN ID
|
For example:
1_TR069_R_VID_2 (First interface, the service is TR069, NAT mode, VLAN ID is 2)
2_INTERNET_B_VID_(Second Interface, Service is INTERNET, Bridge Mode, VLAN is disabled)
2.2 Bridge Mode
Bridge Mode under Multi WAN is different with traditional bridge setting. Bridge mode has no ip address and only work as a bridge between WAN port and LAN port. So Route Connection has to be build to give ip address to local service on device.
Below is an example of bridge mode:
1_TR069_VOICE_INTERNET_R_VID_ is the router connection for the local service.
2_Other_B_VID_ is a bridge connection for the LAN port host.
If the bridge configuration is complex, please refer to the following section for a quick bridge mode setup.
Bridge type:
|
Bridge type
|
Commentary
|
| IP Bridge |
Allow all Ethernet packets to pass. The PC can connect directly to the upper network.
|
|
PPPoE Bridge
|
Allow only PPPoE packet passage. The PC requires PPPoE connection software.
|
|
Hardware IP bridge
|
Packets traverse the hardware switch at wired speed. Wireless port link is not supported. |
DHCP service type:
|
DHCP service type
|
Commentary
|
|
Pass‑Through
|
DHCP packets can be forwarded between WAN and LAN, the gateway’s DHCP server will not assign IPs to LAN port hosts. |
| Snooping DHCP |
When the gateway forwards DHCP packets from the LAN to the WAN, it adds option 82 to the DHCP packet, and it removes option 82 when forwarding the DHCP packet from the WAN to the LAN. The local DHCP service will not assign IPs to LAN port hosts.
|
| Local service |
The gateway will not forward DHCP packets between the LAN and WAN, and it also blocks DHCP packets coming from the WAN port. LAN port hosts can obtain an IP from the DHCP server running on the gateway. |
VLAN Mode :
|
VLAN mode
|
Commentary
|
|
Disable
|
The WAN interface is not tagged. The LAN is not tagged.
|
|
Enable
|
The WAN interface is marked. The LAN is not marked.
|
|
Trunk
|
Valid only in bridge mode. All ports, including WAN and LAN, belong to this VLAN ID and all ports are tagged in this VLAN ID. Tagged packets can traverse WAN and LAN. |
3. Fast Bridge setting
Step 1: Log in to the device’s WEB interface. Go to Administration Page → Operating Mode. Set the operating mode to Basic Mode. Save.
Step 2: Open Network->wan, change Nat Enable to Disable. Save and reboot. The device now operates in Bridge mode.
Step 3: Please connect from the WAN port. Below is an example of the Status Page -> Basic.