Multi WAN is used to distribute different types of services, and the device’s Multi WAN supports distribution of data services, voice services, and management services. By configuring different VLANs, different types of data should be distributed to the corresponding network, for example, the INTERNET VLAN and other VLANs carry data, the VOICE VLAN carries voice, and the TR069 VLAN carries web services, telnet and TR069.
هناك عدة وظائف متقدمة في إعداد Multi WAN:
PPPoE bridge can allow PPPoE packets to pass, which may avoid L2 packet flood to LAN ports.
The HW bridge can act as an L2 Switch to increase bandwidth between WAN and LAN.
VLAN Trunk can allow tagged packets to be forwarded directly to LAN ports.
IPTV can be supported via LAN ports linked to other VLANs.
2. إعداد اتصال الإنترنت
From the WAN page, you can create or delete multiple WAN connections. Below is the default WAN configuration.
2.1 ربط الاسم والخدمة
جدول أسماء الاتصال كما يلي:
|
محتوى
|
تعريف
|
تعليق
|
|
No
|
1~99
|
معرف اتصال WAN
|
|
خدمة
|
TR069
|
The connection supports only management applications, such as TR069, WEB, SNMP and Provision
|
|
|
الإنترنت
|
الاتصال يدعم فقط خدمة الإنترنت
|
|
|
TR069_INTERNET
|
الاتصال يدعم الإدارة وتطبيق الإنترنت
|
|
|
صوت
|
Connection supports only voice applications, such as sip and rtp
|
|
|
TR069_VOICE
|
الاتصال يدعم كل من الإدارة وتطبيق الصوت
|
|
|
VOICE_INTERNET
|
الاتصال يدعم تطبيقات الصوت والإنترنت
|
|
|
TR069_VOICE_INTERNET
|
الاتصال يدعم الإدارة، الصوت وتطبيق الإنترنت
|
|
|
أخرى
|
Connection supports STB
|
| وضع NAT |
B
|
جسر
|
|
|
R
|
راوتر
|
|
معرف VLAN
|
VID
|
معرف VLAN
|
على سبيل المثال:
1_TR069_R_VID_2 (first interface, service is TR069, NAT mode, VLAN ID is 2)
2_INTERNET_B_VID_(Second Interface, Service is INTERNET, Bridge Mode, VLAN is disabled)
2.2 وضع الجسر
وضع الجسر تحت Multi WAN يختلف عن إعداد الجسر التقليدي. لا يحتوي وضع الجسر على عنوان IP ويعمل فقط كجسر بين منفذ WAN ومنفذ LAN. لذلك يجب بناء اتصال Route لتوفير عنوان IP للخدمة المحلية على الجهاز.
في الأسفل مثال على وضع الجسر:
1_TR069_VOICE_INTERNET_R_VID_ is the router connection for the local service.
2_Other_B_VID_ is a bridge connection to the host on the LAN port.
إذا كان إعداد الجسر معقدًا، يرجى الرجوع إلى القسم التالي لإعداد سريع لوضع الجسر.
نوع الجسر:
|
Bridge Type
|
تعليق
|
|
جسر IP
|
السماح بمرور جميع حزم الإيثرنت. يمكن للحاسوب الاتصال بالشبكة العليا مباشرة.
|
|
جسر PPPoE
|
السماح بمرور حزم PPPoE فقط. يحتاج الحاسوب إلى برنامج اتصال PPPoE.
|
|
جسر IP للأجهزة
|
تمر الحزم عبر المفتاح المادي بسرعة سلكية. لا يدعم ربط منفذ لاسلكي.
|
DHCP service type:
|
نوع خدمة DHCP
|
تعليق
|
|
تمرير
|
يمكن توجيه حزم DHCP بين WAN و LAN، ولن يقوم خادم DHCP في البوابة بتخصيص IP للمضيفين على منفذ LAN
|
|
DHCP monitoring
|
When the gateway forwards DHCP packets from LAN to WAN it will add option82 to the DHCP packet, and it will remove option82 when forwarding DHCP packets from WAN to LAN. The local DHCP service will not allocate IP to hosts of the LAN port. |
|
خدمة محلية
|
لن تقوم البوابة بتمرير حزم DHCP بين LAN وWAN، كما أنها تحجب حزم DHCP من منفذ WAN. يمكن لأجهزة منفذ LAN الحصول على IP من خادم DHCP الموجود في البوابة.
|
وضع VLAN:
|
VLAN Mode
|
تعليق
|
|
تعطيل
|
Unlabelled WAN interface. Unlabelled LAN interface.
|
|
Enable
|
WAN interface labeled. LAN unlabeled.
|
|
خط رئيسي
|
صالح فقط في وضع الجسر. جميع المنافذ، بما في ذلك WAN وLAN، تنتمي إلى معرف VLAN هذا وجميع المنافذ مُعلمة في هذا المعرف. يمكن للحزم المُعلمة المرور عبر WAN وLAN.
|
3. إعداد Fast Bridge
Step 1: Log in to the device’s WEB interface. Go to Administration->Operating Mode. Set the operating mode to Basic Mode. Save.
Step 2: Open Network->wan, change Nat Enable to Disable. Save and reboot. The device now operates in Bridge mode.
Step 3: Please log in from the WAN port. Below is an example of the status page -> Basic.