The multicast announcement function allows the initiator to send voice messages to a specified multicast address. All phones listening to this multicast address can receive the initiator's voice messages. The function is similar to broadcasting. The multicast announcement function makes it easy to send announcements to every member of the multicast group.
Operating mechanism :
1. The phone can configure the source multicast address, port and code on the web page.
2. Configure the multicast listen address and port on the web page.
3. The phone initiates the multicast, and all phones listening to the address can receive the multicast content.
Note: All phones must be on the same network segment. The phone can only send/receive broadcasts on the same channel; broadcasts on other channels will be ignored.
Use the multicast announcement function without PBX
Multicast Transmitter Configuration
Log in to the phone's web interface, go to Phone > Line Key Page, set the line key type to Speaker, the value format is IP multicast address:port.


After the settings, the LCD displays as shown below, and multicast is initiated by pressing the Line button. The multicast RTP streams are unidirectional and can only flow from transmitter to receiver.

Configure the multicast receiver
Go to Telephone > IP multicast settings page, configure the corresponding IP address and the listening address you set on the transmitter.

|
Parameter |
Description |
|
Label |
Optional listening multicast name |
|
Listening address |
Listening address:port (The IP address ranges from 224.0.0.0 to 239.255.255.255, and the port number ranges from 1024 to 65535). |
|
Barge sounding |
Vous pouvez sélectionner Priorité d’appel normal dans le Sonorisation Barge. Si la priorité d’un flux RTP multicast entrant est inférieure à la priorité de l’appel normal en cours, le téléphone ignorera automatiquement le flux RTP multicast. Vous pouvez également désactiver le sonorisation barge, et le téléphone ignorera automatiquement tous les flux RTP multicast du réseau local. |
| Ignore DND |
If you don’t want to miss certain emergency paging calls when Do Not Disturb (DND) mode is enabled, you can use the “Ignore DND” feature to set the lowest priority for the paging group. When DND is enabled, paging calls with a priority equal to or higher will be answered automatically, while those with lower priority will be ignored. |
|
Active sound reinforcement priority |
You can enable or disable active speaker priority, a function that determines how the phone handles newly received multicast RTP streams when it is already in a multicast session. If speaker priority is enabled, the phone automatically ignores low‑priority multicast RTP streams, receives high‑priority or equal‑priority multicast RTP streams, and puts the current multicast session on hold. If active speaker priority is disabled, the phone will automatically ignore all received multicast RTP streams. |
|
Multicast codec |
Set the default codec when the phone sends multicast RTP streams. |
Use of multicast audio
When you press the announcement button on the phone, it sends an RTP stream to the pre‑configured multicast address, and other phones configured to listen to this multicast address on the local network can receive the RTP stream and automatically answer the call.

During the call, the sender can press Hold to maintain the current RTP multicast session, the receiver automatically disconnects the RTP multicast session. The sender can press Resume to restore the pending RTP multicast session (RTP multicast session restored). The sender can press EndCall to terminate the ongoing RTP multicast session.
Use multicast announcement function with the PBX
PBX configuration
The phone can use multicast paging with the PBX; we use Yeastar PBX as an example. On the PBX web interface, go to Call Functions > Paging/Intercom Page, click Add.
Type : unidirectional multicast speakerphone or bidirectional multicast speakerphone.
Number: The number of ring tones
Multicast channel IP : multicast address and multicast port


Phone configuration
Connect to the phone’s web interface, register the phone on the Yeastar PBX, then go to Telephone > Line Key
page, set the line key type to Intercom, set the value to the dialing number.

