FIP16/FIP16Plus supports IEEE802.11K/R Fast Roaming, allowing you to walk during a call without interruption. This guide will show how to test this feature.

Eمعدات Reمطلوب

1. نقطتا وصول (AP-1 و AP-2)

2. Two IP phones (FIP16-1 and FIP16-2)

KeyPpointfor Rwander

1. SSID (اسم شبكة الواي فاي) هو نفسه.

2. نوع تشفير اللاسلكي هو نفسه.

3. عنوان IP هو نفسه.(يحصل الهاتف على نفس عنوان IP عند التجوال إلى شبكة أخرى)

4. شبكتان لهما مناطق متداخلة.

إجراء

1. Set up the SSID on both access points, ensuring all settings match except for the channel.

2. Place these two access points and ensure that the two networks have overlapping coverage areas. It will be best if the signal strength in that area is between -60 dBm and -65 dBm.

3. أثناء الوقوف مع FIP16-1 على بُعد أقدام قليلة من AP-1، تأكد من أن FIP16-1 مرتبط بـ AP-1.

4. Make a phone call from FIP16-1 to FIP16-2.

5. Head towards AP-2 so you are right next to it with FIP16-1, and check any connected AP.

How to identify FIP16/FIP16Plus Is roaming successful?

1. لم يتم قطع المكالمة أثناء الاختبار.

2. FIP 16-1 مرتبط بـ AP-2 في الخطوة 5.

كيفية التحقق من نقطة الوصول المتصلة بها to?

طريقة1: Go to قائمة > Status > شبكة، يظهر SSID و MAC address الخاص بـ AP.

Mطريقة 2: سجّل الدخول إلى صفحة إدارة AP أو صفحة إدارة وحدة التحكم AC للتحقق من الجهاز المتصل بشبكته.

What do you do if the phone takes a long time to switch WiFi?

1. تحقق من قوة الإشارة في المناطق المتداخلة بين نقطتي وصول (AP).

Move the phone to overlapping areas, go to list > Status > Network, the number in front of @ is the signal strength.

2. اضبط قيمة العتبة على الهاتف.

ملاحظة: قوة إشارة الواي فاي تتغير عشوائياً، يمكنك اختبار القوة عدة مرات، تجربة عدة عتبات، واختيار القيمة المثلى.

For FIP16Plus:

Go to القائمة > الأساسي > Wi-Fi > إعداد Wi-Fi > قيمة الإشارة. غيّر القيمة إلى قوة الإشارة التي أكدتُها في الخطوة 1.

لـ FIP16:

الطريقة 1: صدّر ملف التكوين (صيغة cfg) متضمنًا هذا المعامل: RoamThreshold=X (X هو قوة الإشارة التي أكدتَها مسبقًا. على سبيل المثال، RoamThreshold=65, يعني أن قوة الإشارة -65dbm.)

Method 2: Connect to the phone via Telnet, run this command: nvram_set RoamThreshold X (X is the signal strength you previously confirmed. For example, nvram_set RoamThreshold 65.

3. ضبط قيمة الفاصل القصير على الهاتف

Go to قائمة > أساسي > Wi-Fi > إعداد Wi-Fi > فترة قصيرة، قلل الفاصل القصير، غيره إلى 3s أو 2s.

4. Check the phone’s firmware version and ensure it is the latest.