بقلم ستيف ف., 23 مارس 2026

1 كيف تعمل لوحات الإنذار؟

لوحة إنذار هي المكون الأساسي لنظام الإنذار. من جانب واحد، تتصل بمختلف المستشعرات (مثل كاشفات الحريق أو الاختراق) عبر ناقل سلكي مزدوج. من الجانب الآخر، تتصل بشبكة PSTN عبر واجهة هاتف، مما يتيح التواصل مع المستقبل.

عادةً ما يتم نشر المستقبل في مركز مراقبة بعيد (شركة مراقبة). تشمل وظائفه الأساسية:

  • استلام إشارات الإنذار من لوحات الإنذار
  • Perform supervisory tasks such as periodic checks ("polling")

The receiver can handle calls from multiple alarm panels and typically provides computer interfaces to send alarm data to systems such as fire monitoring systems (FMS). A typical example is Bosch's Conettix series.


2 ما البروتوكولات المستخدمة بين لوحات الإنذار والمستقبلات؟

على مدى عقود من التطوير، ظهرت أكثر من عشرة بروتوكولات اتصال بين لوحات الإنذار والمستقبلات. تم تقديم هذه البروتوكولات أصلاً من قبل مصنعين مختلفين ولاحقًا أصبحت معتمدة على نطاق واسع في الصناعة.

All these protocols are designed to work over the PSTN network. Technically, they can be classified into three main types:

1. بروتوكولات قائمة على النبض

تنقل هذه البروتوكولات المعلومات باستخدام نوبات نغمية (إشارة نبضية).

Example: "3+1 Standard 1900 Hz Carrier, 1400 Hz ACK."

2. بروتوكولات تعتمد على DTMF

This uses the Dual-tone multi-frequency (DTMF) signal.

The most used protocol today is Contact ID, which falls under this category

3. FSK-based protocols

This relies on Bell 103 Frequency Shift Keying (FSK) technology.

Examples include BFSK and Modem II.


3 تحديات رئيسية لاستبدال خطوط POTS في تطبيقات الإنذار

As shown above, all alarm communication protocols were originally designed for PSTN network transport. In practice, deployment contracts have proven they can operate reliably in that environment, supporting millions of alarm board connections.

However, these protocols inherently rely on the key characteristics of PSTN networks:

  • كمون منخفض
  • نقل متزامن (بدون تشويش)

هذه الاعتمادية تصبح تحديًا رئيسيًا عند الانتقال إلى الشبكات القائمة على IP.

مثال: اكتشاف البروتوكول القائم على المصافحة

في العديد من الأنظمة، يكتشف المستقبلون تلقائيًا البروتوكول المستخدم من قبل لوحة الإنذار عبر نغمات المصافحة.

على سبيل المثال:

مصافحة Contact ID:

o 100 ms at 1400 Hz, 100 ms silence, 100 ms at 2300 Hz

  • بروتوكولات تعتمد على النبض:

عادةً نغمة مستمرة 1400 هرتز أو 2300 هرتز تستمر أكثر من 500 مللي ثانية

بعد إنشاء المكالمة، يرسل المستقبل نغمات مصافحة مختلفة ويحدد البروتوكول بناءً على استجابة اللوحة.

However, this process requires precise timing control. While PSTN networks naturally support this precision, VoIP networks:

  • Jitter
  • فقدان الحزم
  • كمون متغير

تؤدي هذه العوامل إلى اضطراب الإشارات الحساسة للوقت، مما يؤدي إلى فشل الاتصالات. هذا أحد الأسباب الرئيسية لفشل لوحات الإنذار عند الاتصال عبر حلول VoIP القياسية.

Alarm protocols are also sensitive to noise. Traditional VoIP methods—such as increasing the buffer size to compensate for instability—do not work well in this scenario, as they introduce additional delay that further disrupts protocol timing.


4 حل Flyingvoice للاتصال بلوحات الإنذار

4.1 حل عام: V.152 + SBC

The International Telecommunication Union (ITU) defined standard V.152 to enable voice‑band data (VBD) transmission over VoIP networks.

مع ذلك، بسبب:

  • Limited request (VBD represents a small portion of traffic)
  • تعقيد التنفيذ

معظم منصات UC اختارت عدم دعم V.152.

CPE devices to replace POTS lines from flyingvoice — including PR08-Pro, LM150, PR12, and PR18 — fully support V.152. In conjunction with SBC to replace flyingvoice POTS lines, they enable seamless switching between V.152 and standard G.711, allowing interoperability with major UC platforms such as:

  • Netsapiens
  • MetaSwitch
  • Alliance
  • FreeSWITCH

استنادًا إلى كل من التحليل النظري والاختبارات المخبرية، تحت ظروف شبكة مختبر Flyingvoice حيث إجمالي الكمون (ثابت + تذبذب) < 300 مللي ثانية وفقدان الحزم < 3%، يمكن لحلولنا تحقيق معدل نجاح اتصال 99.99%. هذا يجعلها حلًا عمليًا وقابلًا للتوسع لنشر MSP.

4.2 ميزة محسنة: تجاوز معرف الاتصال

In addition to supporting standard protocols, the flyingvoice solution offers advanced bypass capabilities, including:

  • تجاوز الرقم المطلوب
  • تجاوز رقم حساب معرف الاتصال

This is especially useful in renewal scenarios. MSPs can:

  • إعادة توجيه المكالمات إلى مركز مراقبة جديد
  • تعديل معرفات الحساب دون تغيير تكوين لوحة الإنذار

وبالتالي، يصبح النشر أسرع بكثير وأكثر مرونة.

4.3 Transition to IP-based communication: IP Communicator

مع تطور بنية المراقبة، تنتقل العديد من مراكز المراقبة إلى مستقبلات قائمة على IP.

Flyingvoice CPE devices support IP Communicator mode, enabling direct IP reporting to alert monitoring platforms

When running in IP Communicator mode:

  • بروتوكولات PSTN محدودة إلى:

لوحة oAlarm ↔ flyingvoice CPE

  • لا يتم نقلها عبر شبكات VoIP، مما يلغي:

مشكلات التذبذب

oتأثير فقدان الحزم

oحساسية الكمون

  • The CPE converts signals into IP-based reports to transmit to the monitoring center

يتجنب هذا النهج عدم الاستقرار المتعلق بـ VoIP تمامًا.


5 ملخص: أي حل هو الأنسب لخدمتك؟

لأغلب مزودي خدمات UC:

حل V.152 + SBC هو الخيار الأكثر عملية

  • تكامل سريع (في غضون أيام)
  • لا حاجة لتعديل الأنظمة الحالية
  • قدرة موثوقة لاستبدال خطوط POTS

ومع ذلك، في بيئات الشبكة الصعبة—مثل:

  • الارتعاش > 500 ملث
  • فقدان الحزم > 5%
  • انقطاعات اتصال متكررة

IP Communicator is the best choice, it eliminates reliance on VoIP transmission quality and ensures maximum reliability for critical alert communications.