Replacing elevator phones is the most common application among many POTS line replacement projects. In the United States, for example, there are more than one million elevators, many of which need POTS line replacement.

مع ذلك، استبدال خطوط هواتف المصاعد ليس دائمًا بسيطًا كما يبدو.
According to our experience, some elevator brands are equipped with a 'line sharing key'. This can be confusing for those who do not know the elevator model, as the system will show two telephone lines. If these lines are connected incorrectly, elevator panel calls often fail to reach the PBX (UC Cloud), yet you will notice the device retries the call on site.
قد تتساءل: هل هناك مشكلة في CPC (التحكم في الطرف المتصل) للجهاز؟
Connected‑party control: this is a “hang‑up” signal sent by the ATA to inform the elevator phone of call termination.
This abnormal behavior in the call is actually caused by connecting the ATA to the wrong line.
How does REM (remote elevator monitoring) work?
Here is a common REM system architecture.

- Line 1: phone line connected to the REM unit, which manages data communication with the elevator and receives messages from it.
- الكتلة 1: وحدة حماية من ارتفاع التيار الصاعق، والتي تتصل أيضاً بخط هاتف خارجي.
- الكتلة 3: مربع 'مفتاح مشاركة الخط'.
عند ضغط الراكب زر الطوارئ "Help" داخل المقصورة، يتولى نظام REM خط الهاتف ويقوم بإجراء عمليتين مميزتين:
Data transfer First, it establishes a high-speed data connection via an integrated modem to transfer error codes, uplink markers, and root cause data to the REM system (Line 1 in the diagram).
رابط الصوت: بمجرد أن يتم نقل البيانات بنجاح (أو عدم وجود استجابة)، يقوم النظام بإنهاء اتصال البيانات ويتحول إلى وضع الصوت. ثم يربط الراكب المحتجز مباشرةً بمحطة المساعدة الطارئة/قسم الأمن عبر خط الهاتف (الخط 2 في الشكل).

If you want the ATA you install to replace the emergency line, so that when the elevator alarm button is pressed it connects to the "Direct Operator" to talk directly to the trapped passenger, you need to connect the ATA's FXS port to line 1 of the "Line Sharing Switch," instead of the phone line connected to the REM unit.
If the ATA is connected to the phone line corresponding to the REM system instead, the elevator will keep retrying because it cannot connect to the REM unit. From the ATA's perspective, this appears as repeated "hook-off" events, causing the device to continuously detect on-hook and off-hook events, even when the CPC is active.

Immersing in the REM system
نظام REM يدعم بروتوكولات اتصال متعددة.
P100 is a widely used communication protocol in elevator monitoring and control systems that uses DTMF signals. Flyingvoice ATA supports multiple DTMF transmission methods, including RFC2833, RFC4733, Inband and SIP Info. Regardless of the format your SIP system supports, we can provide full compatibility.
بالإضافة إلى ذلك، تم تحسين ATA من Flyingvoice خصيصًا لنقل DTMF الوارد. إذا كنت تستخدم DTMF لبرمجة المصاعد، يمكنك القيام بذلك بثقة، مع العلم أن أخطاء النقل لن تتسبب في فشل البرمجة.
If your REM system transmits a specific type of modem signal (FSK), Flyingvoice ATAs can also facilitate that. Flyingvoice devices support V.150 modem transmission, and with SBC POTS media assistance, the modem signal can be successfully transmitted over 4G networks or in weak network conditions.
How can Flyingvoice help with elevator phone implementation?
1. The entire Flyingvoice product line has been optimized for elevator voice‑call applications, providing configurable CPCs that are compatible with various elevator voice‑call models; it supports a standard 48V power voltage and enhanced DTMF programming.
2. Designed for uninterrupted operation, the Flyingvoice Hardware supports 24‑hour standby mode with battery and internet failure bypass, fully compliant with ASME A17.1/CSA B44 elevator safety codes.
3. Cloud management, Flyingvoice offers a suite of remote configuration/monitoring/diagnostics functions, enhancing not only installation efficiency but also providing significant long‑term operational benefits.
