1 Basic IP phone test functions

Basic IP phone test functions, which are mainly divided into 3 parts: recording capability, call capability and complementary services such as call transfer and conference. The user can evaluate IP phones according to these three aspects. To perform the terminal test, we generally need to specify a SIP server. And Asterisk 1.6 or Asterisk 1.8 is recommended. The reasons are as follows: 1) Asterisk is open source software, it is convenient to obtain the version, you can download it from www.asterisk.org; 2) Asterisk is very popular with rich features, it can support all test programs.

1.1 Recording Capacity

The following table describes the phone recording capacity test, with the SIP server being Asterisk.
Table 1 Test of the IP phone's registration capacity

Recording capacity

No.

Test element

Target test

Operation

Desired result

Confirmation (Y/N)

1

Recording

Check whether the IP phone can register successfully or not.

Create a SIP extension on Asterisk and configure the IP phone.

The IP phone registers successfully

2

Recording time

Check if the registration time meets your needs

Enter the command:

asterisk -rx "sip show peers"

You can see similar information to the following response :

503/503 192.168.1.45 D N A 5060 OK (62 ms)

For the local network test, the registration time must be less than or equal to 180 ms.

3

Maintain registration

Test whether the SIP phone can maintain registered status or not.

Enter the command:

tail -f /var/log/asterisk/full | grep Unregistered

Please continue testing for at least 1 minute.

Once the phone is successfully registered, no Unregistered message should appear.

1.2 Call capacity

The following table describes the basic call capacity tests of the phone.
Table 2: Test of the phone's ability to make calls

Ability to make calls

No.

Test element

Target test

Operation

Desired result

Confirmation (Y/N)

1

Outbound calls

Test if the SIP phone can make outbound calls and the communication quality.

Make calls to all other extensions


Bidirectional calls are established successfully, with neither echo nor typical "buzz" noise heard by either party.

2

Inbound calls

Test whether the SIP phone can receive calls or not and the quality of the communication

Receive calls from any extension

Bidirectional calls are established successfully, with neither party hearing echo or typical “buzz” noise.

1.3 Additional services

The following table describes the tests of the complementary services of the phone.
Table 3 Complementary services test of the phone

Complementary service tests

No.

Test item

Target test

Operation

Desired result

Confirm(Y/N)

1

DTMF sending

Test if the IP phone can correctly send the following DTMF signal: 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, *

Dial *98 to access mailbox 1234567890*

In the Asterisk command-line interface, you can see the following output:

--The user entered '1234567890*'

2

DTMF sending

Test if the SIP phone can correctly send the following DTMF signal: #

Answer an incoming call and press "##"

The user will hear the call transfer warning.

3

Test function key – call transfer

Test call transfer capacity


Accept an incoming call, then press the "call transfer" key and enter the phone number.

Callers can communicate with the target extension of the "call transfer".

4

Test the function key - Do Not Disturb

Test DND

Use the DND button to enable or disable DND


When DND is enabled, the test phone will not receive any incoming calls;
When DND is disabled, the test phone can receive calls.

5

Function key test - Hold

Hold test

Press the HOLD button during an active call

The other party must be on hold and hear the hold music provided by Asterisk.

6

Test function key - Conference

Test conference

Press the "Conference" button during an active call, then call the third party to start the conference.

During the conference, each participant can hear the other two parties and let them hear them.

7

Voicemail function key test

Voicemail test

Leave a message on the phone during testing and press the phone’s “Messaging” button

The test phone can successfully access the voicemail and the user can hear the message.