By SteveF, April 5, 2026

نشأت تقنية المودم في الخمسينيات وكانت من بين أقدم تقنيات الاتصال لربط الحواسيب. في عام 1958، أطلقت AT&T مودم Bell 103، الذي حقق معدل نقل 300 بت في الثانية، ممهداً الطريق لنقل البيانات عبر شبكة PSTN وتمكين الاتصالات الحاسوبية عن بُعد للمرة الأولى.

From the nineteen-sixties to the nineteen-eighties, modem technology spread rapidly in commercial and industrial applications. At that time, all computers were equipped with RS232 serial ports — whereas all modern computers have WiFi. The DTE/DCE interface and AT command set were unified during this period. Today, we still refer to connected devices that use 4G/5G technology as cellular modems, and these devices continue to rely on the AT command set.

من الصعب على شباب اليوم تخيّر أن الناس قبل 30 عامًا كانوا يصلون إلى الإنترنت عبر جهاز يُسمّى "مودم" (كما هو موضح في الصورة أعلاه). مع ازدهار الإنترنت في التسعينيات، ارتفعت سرعات المودم بسرعة—from معدلات أولية 9.6 Kbps و14.4 Kbps إلى 33.6 Kbps (معيار V.34)، ثم تطورت إلى الحد النظري 56 Kbps عبر الخطوط التناظرية (معايير V.90/V.92).

56 كbps تمثّل الحد النظري لخطوط PCM، لكن هذا المعدل لا يلبي احتياجات تطور الإنترنت. وبالتالي، مع دخولنا عام 2000، تم استبدال المودم بسرعة بتقنية xDSL ثم بتقنية PON. اليوم، التقنية السائدة للإنترنت السلكي هي Giga PON، وهي تتطور حاليًا نحو 10G PON.

However, the modem technology application extends beyond just internet connectivity. Even before the internet age, modems were widely used in various scenarios requiring remote access—such as POS systems, SCADA applications, alarm panels, or remote programming of emergency phones. These applications remain common today as well.


1. Challenges posed by PSTN conversion to modem applications

The PSTN network is a time‑synchronized network. Although the PSTN network may experience transmission errors due to environmental interference (such as lightning strikes), it is characterized by a very small and constant latency with no jitter. In contrast, IP networks are asynchronous; jitter ranging from tens to even hundreds of milliseconds is common, and connection outages lasting several seconds can occur.

بروتوكولات المودم تعتمد بشكل كبير على ميزات التزامن في شبكة PSTN. على سبيل المثال، لنأخذ تنسيق SIA FSK Format F2، وهو بروتوكول مودم مشابه لـ Bell 103.

As shown in the figure above, the SIA FSK Format F2 requires detecting the start bit before receiving 8 data bits at a baud rate of 42.7. This protocol can tolerate a certain amount of jitter, but clearly the maximum jitter duration must not exceed 23.42 ms (1000 ms / 42.7); otherwise it will cause "misalignment" of data detection, leading to communication errors.

The SIA FSK F2 format is a slow‑speed modem communication protocol. Although it also uses FSK, its baud rate is only 42.7, far below the 300 bps specified by Bell103. However, the SIA FSK F2 format can tolerate only 23.42 ms of timing jitter — a clear requirement that is extremely strict for IP networks. This is why most UC platforms designed for voice communications cannot support direct modem connections.


2. معايير ITU لتطوير حلول Modem Over IP

《ITU V.152 Procedures for Supporting Voice‑Band Data over IP Networks》 aims to provide a general transmission method for Voice‑Band Data (VBD) based on G.711. It defines a basic approach for automatic recognition of voice codecs such as G.729 and for switching between voice and VBD modes. At the same time, V.152 also defines the Assure VBD mode that supports RED and FEC.

فيما يتعلق بوضع VBD غير المضمون المحدد في V.152، لا يمكنه عادةً العمل بسبب حساسية اتصال المودم للارتعاش. من ناحية أخرى، يعمل وضع VBD المضمون بشكل ممتاز في البيئات التي لا يكون فيها الارتعاش شديدًا. للأسف، معظم منصات UC لا تدعم مباشرة RED أو FEC.

When jitter is high, V.152 also experiences a noticeable increase in failure rates. In such cases, it becomes necessary to use another standard specified by ITU—V.150.

The main content of the V.150 specification is identified in "V.150.1 Modem-over-IP networks: Procedures for the end-to-end connection of V-series DCEs", which defines the interconnection model.

يحدد V.150.1 أيضًا بروتوكول SPRT (Simple Packet Relay Transport)، الذي ينفّذ نقلًا موثوقًا يعتمد على UDP. يعالج V.150.1 مشكلة نقل الإشارة عبر المودم عن طريق فك تشفير بروتوكول المودم على جهاز البوابة (مثل PR12 أو PR18 من Flyingvoice) وتحويله إلى حزم IP، التي تُنقل بعد ذلك عبر بروتوكول SPRT إلى الطرف المتصل (عادةً جهاز بوابة آخر يدعم V.150.1) وتُعاد تحويلها إلى إشارات مودم. بما أن بروتوكول المودم يُفك تشفيره محليًا إلى حزم IP، فإن تأثيرات تذبذب شبكة IP تُتجنّب طبيعيًا، مما يتيح نقل مودم موثوق.


3. How does replacing POTS lines from Flyingvoice MSPs help build a reliable modem communication platform?

يمكن لمزودي الخدمات المدارة (MSPs) الاستفادة من SBC وسائط POTS من Flyingvoice لتمكين وضع V.152 Assure VBD، أو يمكنهم نشر محطات POTS من Flyingvoice مباشرةً في الطرفين واستخدام بروتوكول V.150 لتنفيذ نقل مودم موثوق.

3.1. Implement V.152 and ensure VBD mode using Flyingvoice Media SBC

As shown in the figure above, the Flyingvoice POTS Media SBC is a cloud server deployed on AWS. It is responsible for converting data in V.152 Assure mode—where the RED/FEC method is enabled—into standard G.711 data and sending it to the UC platform deployed by the managed service provider (MSP). Without having to modify anything in the existing network, the MSP can benefit from the Flyingvoice POTS device to provide reliable modem transport services.

V.152 + SBC mode is suitable for scenarios with relatively good network conditions. According to Flyingvoice lab assessment, the total end‑to‑end latency (fixed delay + jitter) should be less than 300 ms, and packet loss should be below 3 %.

3.2. Deploy Flyingvoice POTS devices at both ends to achieve direct V.150 connectivity.

بالنسبة لمواقع التركيب ذات ظروف الشبكة الضعيفة—مثل تلك التي تشهد تذبذبًا متكررًا يتجاوز 500 مللي ثانية، أو معدلات فقدان حزم أكبر من 5%، أو انقطاعات شبكة متكررة—يُعد بروتوكول V.150 خيارًا أفضل.

However, this requires both CPE devices to support the V.150 standard. Although Flyingvoice does not require both parties to use Flyingvoice devices, for easier management and maintenance we recommend using Flyingvoice POTS devices (such as PR12 or PR18) on both sides.


4. الملخص

In the United States today, modems are still widely used in legacy devices such as alarm panels, emergency phones (elevators and blue boxes), inbound programming, SCADA systems, point‑of‑sale terminals, and more. With the imminent shutdown of the PSTN network, communication issues with these devices must be addressed urgently.

Managed Service Providers (MSPs) can benefit from Flyingvoice CPE devices (such as PR12 and PR18) and SBCs and POTS media to quickly integrate with existing UC platforms and provide reliable migration services to customers.